Musical Instrument Parts
The plastic bits around an instrument are the ones that break, and the ones nobody stocks — a case catch, a stand foot, the clip that holds the music up. They are quick to model, cheap to print, and once the file exists the next one is trivial.
Serving South & West Yorkshire and nearby, and posting parts across the UK · Guide prices in seconds · No account needed
Get a musical instrument parts estimate
Upload your file or describe the part. We review printability before confirming anything.
Common uses
- Case catches, feet, hinge parts and internal formers
- Music stand clips, pegs, desk fittings and page holders
- Practice mutes, dampers and instrument stand parts
- Capos, thumb rests, strap fittings and end pins
- Woodwind and brass accessory spares: key guards, stand pegs, swab weights
- Pedalboard and amp furniture: mounts, feet and cable clips
Accessories and spares, not the instrument itself
The honest limit first. We do not print soundboards, bridges, nuts, saddles, necks, tuning pegs or anything else that carries string tension or sits in the acoustic path of an instrument. Two reasons, and both are real. A printed part is layered, which makes it weakest across the layers and prone to creeping slowly under a constant load — string tension is exactly that load, applied for years. And the parts that make an instrument sound like itself are made from what they are made from for a reason; swapping a tonewood or bone component for extruded plastic changes the instrument, and not in a direction anyone asked for. If your guitar needs a bridge, that is a luthier's job. Case fittings, stand parts, mutes, clips and accessories are ours.
Getting the fit right
Most of this work is copying something that has snapped. Send the original, in pieces if that is what you have, or measurements and photos with a rule in shot. The details that decide whether a copy works are the boring ones: thread sizes on stands and mic clips, spindle and shaft diameters, the depth of a socket, the exact spacing of two screw holes. Tell us the make and model of the instrument or stand if you know it. We model the part, share the file so you can check it against the real thing, and print once you are happy. If the fit is tight we print a test piece of just that feature first rather than a whole part.
Material, and what a hot car does to it
PLA is rigid, prints crisply and is fine for something that lives on a music stand indoors. It is a poor choice for anything that travels: the boot of a car in July gets past the temperature where PLA softens, and a case fitting that arrives at the gig deformed is worse than useless. PETG is the sensible default for gigging kit — tougher, more heat-tolerant, less brittle. TPU is the pick for grips, feet, bumpers and mutes where you want give and quiet. ASA if it lives outdoors or in a van. Layer lines will be visible; matte filament and a considered print orientation hide most of it, and a light sand and a rattle-can does the rest if you want it smooth.
How it works
Send your file or describe the part
Upload an STL, OBJ, 3MF or STEP file, or tell us what you need with photos and a few measurements.
Get a guide price
When we can read the geometry we estimate from it straight away — material, print time, supports and quantity all priced openly.
We check printability, then confirm
A person reviews orientation, wall thickness and supports, flags anything that will not print well, and confirms your final quote before any work starts.
Musical Instrument Parts — example prices
Worked examples on real models from our print library, priced by the same calculator that estimates your own part. Sizes span small to large so you can see how cost moves with the part.
| Example part | Size | PLA | PETG | ABS / ASA |
|---|---|---|---|---|
| J-Hook (small) | 23 × 34 × 10 mm | £1.28 – £1.63 | £1.36 – £1.73 | £1.54 – £1.96 |
| J-Hook (large) | 34 × 50 × 14 mm | £2.66 – £3.40 | £2.82 – £3.60 | £3.18 – £4.06 |
| Wall Hook (utility) | 40 × 35 × 55 mm | £5.06 – £6.46 | £5.34 – £6.83 | £5.98 – £7.64 |
| Garage Tool Rail (6-hook) | 45 × 228 × 55 mm | £27.16 – £34.71 | £28.67 – £36.64 | £32.05 – £40.96 |
Guide prices for a single unit, calculated from the measured geometry of each example model — not fixed quotes. Small parts land at or near the £0 minimum order, and per-unit prices fall with quantity. Your price depends on your own part, its material and its printability. How pricing works.
Example models for musical instrument parts
Open-source designs from our print library that show the kind of part this service suits. View any of them for a full material and quantity price breakdown.
Wall Hook (utility)
Display Plinth (medium)
Control Knob (large)
Display Plinth (small)
These are open-source example designs (CC0) we publish to show what the process suits and what it costs — not a record of past jobs. Prices shown are examples in PLA.
Musical Instrument Parts — FAQ
Can you print a replacement bridge, nut or soundboard part?+
No. Anything under string tension or in the acoustic path is out — printed plastic creeps under constant load and it changes how the instrument sounds. That work belongs with a luthier or repairer. Ask us for the accessories and the case and stand spares instead.
Will a printed mute sound like a proper one?+
It will sound like a printed mute. Mutes work through mass and material damping, and extruded plastic does not behave like felt, rubber or brass — so expect a usable practice mute with its own character rather than a like-for-like copy of the one you had. If the mute is for a recording or a performance, buy the real one.
My case catch snapped and the manufacturer is long gone. Can you copy it?+
That is a good fit for this. Send the broken catch and its mounting screws, or a matching one from the other side of the case, and we will recreate it. A small batch is barely more than a single part once the design work is done.
Can you match the finish of my existing hardware?+
Not exactly, and we would rather say so now. Filament comes in a limited palette, there is no chrome or plating, and FDM leaves layer lines. Matte black is the most forgiving. If a part needs to disappear next to a chrome fitting, it is worth planning to sand and paint it.
How much does musical instrument parts cost?+
There is no fixed per-item rate — price comes from how much plastic the part uses, how long it takes to print, how much support and finishing it needs, and how many you want. The example table above shows what real parts of this kind work out at. Upload your file for a guide price on your own part.
How long does it take?+
It depends on the size of the part, the queue and the material. Tell us your deadline when you enquire and we will tell you honestly whether it is achievable before you commit.
Can I order one of the models from your library?+
Yes. Every model in our print library is a design you can have printed — pick one, choose a material and quantity, and the example price on its page is your starting point. You can also download the file and take it elsewhere; they are all CC0.
Are my files kept private?+
Yes. Uploaded files go to private storage, are never made public, and are only used to quote and produce your job.
Worth reading first
Practical guides that help you get a better part and a more accurate quote.
What Is TPU (Flexible Filament)?
TPU is printable rubber. It bends, grips, seals and absorbs shock — and it behaves nothing like PLA, which is the whole point and the whole difficulty.
Nylon and Carbon Fibre Parts
The engineering end of FDM. Nylon is tough and wear-resistant; carbon fibre makes it stiff and stable. Both are harder work — here is when that pays off.
How to Copy a Part Without CAD
No file, no drawing, just a broken part and a pair of calipers. That is a perfectly normal starting point — here is how the process actually works.
Other services
Get a 3D print estimate
Upload your file or describe the part. We review printability before confirming anything.